1. Hello there guest and Welcome to Modular Fox Mustangs home of the 2V, 3V, 4V, Coyote Modular Mustang Conversion Information Website!
    To gain full access you must Register. Registration is free and it takes only a few moments to complete.
    Already a member? Login here then!

    Dismiss Notice

Another F100 mod swap

Discussion in 'All Other Conversions' started by jaa55, May 9, 2015.

  1. jaa55

    jaa55 Active Member

    Messages:
    24
    Likes Received:
    5
    Trophy Points:
    33
    My dad had recently purchased a aluminum headed 390 paired with a t56 and 4 link. I loved the truck so much I decided to build my own version.

    Started out as a 68 harbour blue SWB truck, 352 FE
    [​IMG]
    [​IMG]

    Then I bought this for a donor, 2006 CVPI
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]

    Next I got an epic deal on a super low mileage 3v 4.6
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
     
  2. jaa55

    jaa55 Active Member

    Messages:
    24
    Likes Received:
    5
    Trophy Points:
    33
    [​IMG]

    Then the truck turned green, found an even better cab
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]

    Wiring mess
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]

    First drive, no mufflers needs tuned but it runs and the drive by wire works so I'm happy

    [​IMG]
     
    Bill likes this.
  3. Bill

    Bill Well-Known Member Staff Member Donator

    Messages:
    1,412
    Likes Received:
    245
    Trophy Points:
    93
    That's a nice toy.
     
  4. DOHCfoxLX

    DOHCfoxLX Active Member

    Messages:
    57
    Likes Received:
    19
    Trophy Points:
    28
    Another one of my dream builds
     
  5. jaa55

    jaa55 Active Member

    Messages:
    24
    Likes Received:
    5
    Trophy Points:
    33
    Still needs more wire cleaning up and everything is covered in dust now. But exhaust is built and on. Sounds great
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
     
  6. Sittinlow88

    Sittinlow88 New Member

    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    1
    I have a 71' F100 and a 99' 2V 4.6 ready to go. Can you please give me some more info on your wiring and PATS disable? I have the complete donor vehicle so I can grab anything needed, I wish to keep the engine management as simple as possible and elementary as much wiring as I can. Anything you can pass along would be greatly appreciated!
     
  7. jaa55

    jaa55 Active Member

    Messages:
    24
    Likes Received:
    5
    Trophy Points:
    33
    The 06' P71 computer I used does not have PATS. Although when I did my fox mod swap i used a 96 GT computer with PATS, and I had it disabled it in the tune. Wiring is simple coming out of the truck. Basically a couple 12v into the cab and a switched ignition 12v coming back out that you will use to trip your ECM relay. Tons of things can be eliminated. I suggest in investing in a wiring schematic from all diy data
     
    Bill likes this.
  8. Sittinlow88

    Sittinlow88 New Member

    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    1
    Thank you.
    I have talked with Eric Brooks of Brooks speed in Orlando, he makes custom tunes sent via email for the SCT tuners for $200. I need to find an SCT now
     
  9. hipoman

    hipoman Active Member

    Messages:
    119
    Likes Received:
    23
    Trophy Points:
    38
    Too cool!
     

Share This Page